Health Screening Strategies for Artisanal and Small-Scale Miners for Tuberculosis, Human Immunodeficiency Virus and Silicosis: A Case of the USAID-Supported Kunda Nqob'iTB Project in Zimbabwe.

Artisanal and small-scale mining is characterized by excessive exposure to physical, chemical, ergonomic, psychosocial and biological hazards. There is a high burden of tuberculosis (TB), human immunodeficiency virus (HIV) infections and silicosis among artisanal and small-scale miners (ASMs). The aim of this project report is to describe lessons learned from strategies implemented to reach ASMs with screening services for TB, HIV and silicosis in Zimbabwe through the Kunda-Nqob'i TB (KNTB) project supported by the United States Agency for International Development (USAID). The intervention package for screening ASMs for TB, HIV and silicosis included service provision through two occupational health clinics at two provincial hospitals and a mobile workplace-based screening (WBS) facility at the mining sites. From 1 October 2020 to 30 September 2023, 10,668 ASMs were screened, with a high number of cases of silicosis (21%) and TB (7.4%). There was a high burden of HIV (30%) in ASMs attending the occupational health clinics. The two occupational health clinics screened 3453 ASMs, while the mobile WBS activities screened 7215 ASMs during the period. A total of 370 healthcare workers (doctors/clinical officers, nurses, environmental health technicians and district tuberculosis and Leprosy control officers) were trained on TB and the fundamental diagnostic principles of silicosis. The KNTB project has been successful in reaching out to many ASMs operating in remote and hard-to-reach mining areas. The KNTB project has brought to light the positive health-seeking behavior of ASMs operating in remote areas. The project has brought to the fore the effectiveness of multi-stakeholder engagement and collaboration in reaching out to ASMs in remote areas with health screening services. There is a high burden of TB, HIV and silicosis in ASMs. Screening for TB, HIV and silicosis using workplace-based screening and occupational health clinics is an effective strategy and should be rolled out to all areas with high artisanal and small-scale mining activity.

Knowledge, Attitudes, and Practices of Artisanal and Small-Scale Miners regarding Tuberculosis, Human Immunodeficiency Virus, and Silicosis in Zimbabwe.

In Zimbabwe, artisanal and small-scale miners (ASMs) have a high prevalence of tuberculosis (TB), human immunodeficiency virus (HIV), and silicosis. Previous studies on ASMs utilised programme data, and it was not possible to understand reasons for the high prevalence of these comorbidities. We conducted a cross-sectional study to investigate the knowledge, attitudes, and practices of ASMs regarding TB, HIV, and silicosis. We enrolled a convenience sample of 652 ASMs. Their mean (standard deviation) age was 34.2 (10.8) years. There were 602 (92%) men and over 75% had attained secondary education. A total of 504 (80%) of the ASMs knew that TB is a curable disease, and 564 (87%) knew that they were at higher risk of TB than the general population. However, they were less likely to know that HIV increases the risk of TB disease, 340 (52%), with only 226 (35%) who perceived the risk of TB infection to be high among ASMs. Only 564 (59%) were aware that silica dust causes permanent and incurable lung diseases. Six hundred and twenty (97%) showed a positive attitude towards healthcare when they were sick, and 97% were willing to use special respirators to prevent dust inhalation. On practices, only 159 (30%) reported consistent use of either cloth or respirators to prevent dust inhalation. Three hundred and five (49%) ASMs reported consistent use of condoms outside their homes and 323 (50%) reported use of water to suppress dust. Only 480 (75%) of ASMs sought healthcare services when sick. ASMs cited challenges of accessing healthcare services due to lack of money to pay for healthcare (50%), long distances to clinics (17%), and the shortage of medicines at clinics (11%). Effective control of TB, silicosis, and HIV among ASMs requires addressing the identified knowledge gaps and barriers that are faced by ASMs in accessing personal protective equipment and healthcare services. This will require multisector collaboration and the involvement of ASMs in co-designing a package of healthcare services that are tailored for them.

Health and Safety Risk Mitigation among Artisanal and Small-Scale Gold Miners in Zimbabwe.

Artisanal and small-scale gold mining (ASGM) is often associated with no or compromised attention to health and safety. Although headlines of fatal accidents in Zimbabwe characterise ASGM, little attention is paid to prevention strategies. This study, therefore, explores health and safety risk mitigation in ASGM in Zimbabwe to inform prevention strategies. A qualitative design was used with focus group discussions and in-depth interviews. Data were analysed using thematic analysis, coding, and descriptive statistics. Reported factors contributing to compromised health and safety included immediate causes, workplace factors, ASM related factors, and contextual factors, with interconnectedness between the causal factors. In addition, factors related to ASGM were significant. For risk mitigation, formalisation, organisation of risk reduction, behaviour change, and enforcement of prevention strategies is proposed. A multi-causal analysis is recommended for risk assessment and accident investigation. A multi-stakeholder approach could be considered for risk mitigation including community and public health interventions. However, risk mitigation has been characterised by gaps and weaknesses such as lacking ASM policy, lack of capital, poor enforcement, negative perceptions, and non-compliance. Therefore, we recommend addressing the threats associated with health and safety mitigation to ensure health and safety protection in ASGM.

The Triple Burden of Tuberculosis, Human Immunodeficiency Virus and Silicosis among Artisanal and Small-Scale Miners in Zimbabwe.

Artisanal and small-scale mining is characterized by an excessive exposure to silica-containing dust, overcrowding, poor living conditions and limited access to primary health services. This poses a risk to tuberculosis, HIV infection and silicosis. The main purpose of the study is to evaluate the burden of tuberculosis, HIV and silicosis among artisanal and small-scale miners. We conducted a cross sectional study on 3821 artisanal and small-scale miners. We found a high burden of silicosis (19%), tuberculosis (6.8%) and HIV (18%) in a relatively young population, with the mean age of 35.5 years. Men were 1.8 times more likely to be diagnosed with silicosis compared to women, adjusted prevalence ratio [aPR = 1.75 (95% CI: 1.02-2.74)]. Artisanal and small-scale miners who were living with HIV were 1.25 times more likely to be diagnosed with silicosis compared to those who were negative, [aPR = 1.25 (1.00-1.57)]. The risk of silicosis increased with both duration as a miner and severity of exposure to silica dust. The risk of tuberculosis increased with the duration as a miner. Zimbabwe is currently experiencing a high burden of TB, silicosis and HIV among artisanal and small-scale miners. Multi-sectoral and innovative interventions are required to stem this triple epidemic in Zimbabwe.

Reducing disease and death from Artisanal and Small-Scale Mining (ASM) - the urgent need for responsible mining in the context of growing global demand for minerals and metals for climate change mitigation.

Artisanal and small-scale mining (ASM) takes place under extreme conditions with a lack of occupational health and safety. As the demand for metals is increasing due in part to their extensive use in 'green technologies' for climate change mitigation, the negative environmental and occupational consequences of mining practices are disproportionately felt in low- and middle-income countries. The Collegium Ramazzini statement on ASM presents updated information on its neglected health hazards that include multiple toxic hazards, most notably mercury, lead, cyanide, arsenic, cadmium, and cobalt, as well as physical hazards, most notably airborne dust and noise, and the high risk of infectious diseases. These hazards affect both miners and mining communities as working and living spaces are rarely separated. The impact on children and women is often severe, including hazardous exposures during the child-bearing age and pregnancies, and the risk of child labor. We suggest strategies for the mitigation of these hazards and classify those according to primordial, primary, secondary, and tertiary prevention. Further, we identify knowledge gaps and issue recommendations for international, national, and local governments, metal purchasers, and employers are given. With this statement, the Collegium Ramazzini calls for the extension of efforts to minimize all hazards that confront ASM miners and their families.

Accidents, Injuries, and Safety among Artisanal and Small-Scale Gold Miners in Zimbabwe.

Artisanal and small-scale gold mining (ASGM) employs 14-19 million people globally. There is limited research on accidents, injuries, and safety in Zimbabwe's ASGM. This study investigates the prevalence of accidents and injuries, as well as the associated risks and existing safety practices. A cross-sectional survey was conducted among artisanal and small-scale gold miners. Data from 401 participants were analyzed using descriptive statistics and regression analysis. The prevalence of accidents and injuries was 35.0% and 25.7%. Accidents associated with experiencing injuries included mine collapses and underground trappings. The major injury risk factors were digging, blasting, being male, being 18-35 years old, crushing, and the underground transportation of workers and materials. Injuries were reported highest among the miners working 16 to 24 h per day. Participants had heard about personal protective equipment (PPE). There was training and routine inspections mainly on PPE use. Mine owners and supervisors were reported as responsible for OSH, which was mainly PPE use. Practices including the use of wire winch ropes and escape routes were rare. There was ignorance on underground mine shaft support. The mining regulations that had the potential to introduce comprehensive safety controls were not adaptable. We recommend applicable health and safety regulations for Zimbabwe's ASGM.

Hazards and Control Measures among Artisanal and Small-Scale Gold Miners in Zimbabwe.

Background: In 2017 around 14-19 million miners were exposed to multiple hazards in artisanal and small-scale gold mining (ASGM). ASGM is characterized by basic and compromised mining methods with either very limited control of hazards or none at all. There is little knowledge about health and safety among artisanal and small-scale gold miners in Zimbabwe. Objective: This study explores the interaction between hazards, control measures, and health and safety in Zimbabwe's ASGM. Methods: Triangulation and mixed methods were applied using standardized questionnaires, Hazard Identification and Risk Assessment (HIRA), focus group discussions (FGDs), and summary notes from in-depth interviews (IDIs). Data were analyzed using descriptive statistics, regression analysis, and thematic analysis. Findings: Quantitative data were collected through HIRA, which was conducted on 34 mining sites. 401 participants, selected through multi-stage sampling, were assessed through standardized questionnaires. Qualitative data was collected through six FGDs, and existing summary notes from 84 IDIs. The most prioritized hazards from the questionnaires were silica dust, noise, and workplace violence as indicated by 238 (62.0%), 107 (26.8%), and 104 (26.7%) respondents (respectively). HIRA identified noise, dust, unsafe shafts, violence, poor sanitation, and poor hygiene as key hazards requiring urgent attention. A key finding of this study was the poor application of the hierarchy of controls in managing workplace hazards. After adjusting for confounders, association with experiencing health and safety challenges was working underground (AOR = 2.0, p = 0.03), workplace violence (AOR = 3.3, p = 0.002), and long working hours (AOR = 2.8, p = 0.019). Injuries and fatalities were common without mitigation strategies. Conclusions: ASGM in Zimbabwe is characterized by underground mining, long working hours, and workplace violence. The poor application of the hierarchy of controls is characterized by increased workplace injuries and fatalities. We recommend following the hierarchy of control measures in ASGM: elimination, substitution, engineering, administrative, and personal protective equipment.

Job Exposure Matrix for Chrysotile Asbestos Fibre in the Asbestos Cement Manufacturing (ACM) Industry in Zimbabwe.

Occupational chrysotile asbestos exposure data in Zimbabwe is limited. The aim of this study was therefore to develop a job exposure matrix (JEM) specific to the chrysotile asbestos cement manufacturing industry using the available personal exposure concentration data. Quantitative personal exposure chrysotile fibre concentration data collected by the two factories from 1996 to 2020 were used to construct the JEM. Exposure groups from which data was extracted were classified based on the Zimbabwe Standard Classification of Occupations (ZSCO), 2009-2019. Analysis of amphiboles in raw chrysotile was done by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Descriptive statistics, namely mean, standard deviation and range were computed for the main variable, job/occupation. All jobs/occupations in both factories had annual mean personal exposure concentrations exceeding the OEL of 0.1 f/mL, except for the period from 2009 to 2016 in the Harare factory and the period from 2009 to 2020 in the Bulawayo factory. Despite the Harare factory having no AC manufacturing activity since 2017, personal exposure concentrations showed elevated levels for the period 2018-2020. Amphiboles were detected in almost all bulk samples of chrysotile asbestos analysed. The established JEM, which has been generated from actual local quantitative exposure measurements, can be used in evaluating historical exposure to chrysotile asbestos fibre, to better understand and predict occurrence of ARDs in future.

Prediction of Asbestos-Related Diseases (ARDs) and Chrysotile Asbestos Exposure Concentrations in Asbestos-Cement (AC) Manufacturing Factories in Zimbabwe.

The use of historical asbestos measurement data in occupational exposure assessment is essential as it allows more quantitative analysis of possible exposure response relationships in asbestos-related disease (ARD) occurrence. The aim of this study was to predict possible ARDs, namely lung cancer, mesothelioma, gastrointestinal cancer, and asbestosis, in two chrysotile asbestos cement (AC) manufacturing factories. Prediction of ARDs was done using a specific designed job-exposure matrix for airborne chrysotile asbestos fibre concentrations obtained from the Harare and Bulawayo AC factories and through application of OSHA's linear dose effect model in which ARDs were estimated through extrapolation at 1, 10, 20, and 25 years of exposure. The results show that more cancer and asbestosis cases are likely to be experienced among those exposed before 2008 as exposure levels and subsequently cumulative exposure were generally much higher than those experienced after 2008. After a possible exposure period of 25 years, overall cancer cases predicted in the Harare factory were 325 cases per 100,000 workers, while for the Bulawayo factory, 347 cancer cases per 100,000 workers exposed may be experienced. Possible high numbers of ARDs are likely to be associated with specific tasks/job titles, e.g., saw cutting, kollergang, fettling table, ground hard waste, and possibly pipe-making operations, as cumulative exposures, though lower than reported in other studies, may present higher risk of health impairment. The study gives insights into possible ARDs, namely lung cancer, mesothelioma, gastrointestinal cancer, and asbestosis, that may be anticipated at various cumulative exposures over 1, 10, 20, and 25 years of exposure in AC manufacturing factories in Zimbabwe. Additionally, results from the study can also form a basis for more in-depth assessment of asbestos cancer morbidity studies in the AC manufacturing industries.

Biomonitoring of arsenic, cadmium and lead in two artisanal and small-scale gold mining areas in Zimbabwe.

People living and working in artisanal and small-scale gold mining (ASGM) areas are frequently exposed to elemental mercury (Hg), which is used for gold extraction. However, additional exposure to other toxic metals such as arsenic (As), cadmium (Cd) and lead (Pb) may result from mining-related activities and could be ingested via dust, water or food. In these areas, only limited biomonitoring data is available for toxic metals other than Hg. In particular, data about the exposure to As, Cd and Pb is unavailable for the Zimbabwean population. Therefore, we conducted a cross-sectional study in two ASGM areas in Zimbabwe to evaluate the internal exposure to these metals. In total, urine and blood samples from 207 people that identified themselves as miners were collected and analysed for As and Cd in urine as well as Pb in blood by GF-AAS. Median levels (interquartile ranges in µg/l) of As and Pb were 9.7 µg/l (4.0, 18.5) and 19.7 µg/l (12.5, 34.5), respectively. The 25th percentile and the median for Cd were below the limit of detection (0.5 µg/l); the 75th percentile was at 0.9 µg/l. The results were compared to reference values found for the general population in the USA and Germany, and a significant number of participants exceeded these values (As, 33 %; Cd, 27 %; Pb, 32 %), indicating a relevant exposure to toxic metals. Although not representative for the Zimbabwean population, our results demonstrate that the exposure to toxic metals is relevant for the public health in Zimbabwe and requires further investigation.

Analysis of the Mercury Distribution in Blood as a Potential Tool for Exposure Assessment - Results from Two Artisanal and Small-Scale Gold Mining Areas in Zimbabwe.

People in artisanal and small-scale gold mining (ASGM) areas are frequently exposed to high levels of mercury (Hg). Hg analyses in urine and whole blood are the gold standard of biomonitoring, although this may not provide sufficient information about the source of exposure, e.g., due to the use of Hg for gold extraction or due to nutrition. To evaluate, whether the pharmacokinetic properties of individual Hg species may be useful for exposure assessment, we determined the Hg levels in different blood components from 199 participants. Therefore, whole blood was centrifuged on-site to yield erythrocytes and plasma. Globin was isolated from the erythrocytes by precipitation with ethyl acetate. Albumin was isolated from plasma by gradual precipitation with saturated ammonium sulfate solution. Hg levels in all samples were determined by using a direct Hg analyzer. Median Hg levels for whole blood, erythrocytes, and plasma were 2.7, 3.7, and 1.3 µg/l, respectively. In globin and albumin, median Hg levels were 10.3 and 7.9 µg/kg, respectively. The distribution of Hg was strongly correlated with whole blood Hg levels (p < 0.01) and the time between the last use of Hg and the date of the participation (p < 0.01). The results suggest that the distribution of Hg in blood is substantially affected by the extent and the frequency of the exposure to elemental Hg. Therefore, the analysis of Hg in erythrocytes and plasma may be a valuable tool for Hg exposure assessment in ASGM areas.

Tuberculosis and Silicosis Burden in Artisanal and Small-Scale Gold Miners in a Large Occupational Health Outreach Programme in Zimbabwe.

Artisanal and small-scale miners (ASMs) labour under archaic working conditions and are exposed to high levels of silica dust. Exposure to silica dust has been associated with an increased risk of tuberculosis and silicosis. ASMs are highly mobile and operate in remote areas with near absent access to health services. The main purpose of this study was to evaluate the prevalence of tuberculosis, silicosis and silico-tuberculosis among ASMs in Zimbabwe. A cross-sectional study was conducted from 1 October to 31 January 2021 on a convenient sample of 514 self-selected ASMs. We report the results from among those ASMs who attended an outreach medical facility and an occupational health clinic. Data were collected from clinical records using a precoded data proforma. Data variables included demographic (age, sex), clinical details (HIV status, GeneXpert results, outcomes of chest radiographs, history of tuberculosis) and perceived exposure to mine dust. Of the 464 miners screened for silicosis, 52 (11.2%) were diagnosed with silicosis, while 17 (4.0%) of 422 ASMs were diagnosed with tuberculosis (TB). Of the 373 ASMs tested for HIV, 90 (23.5%) were sero-positive. An HIV infection was associated with a diagnosis of silicosis. There is need for a comprehensive occupational health service package, including TB and silicosis surveillance, for ASMs in Zimbabwe. These are preliminary and limited findings, needing confirmation by more comprehensive studies.

Trends in Airborne Chrysotile Asbestos Fibre Concentrations in Asbestos Cement Manufacturing Factories in Zimbabwe from 1996 to 2016.

Zimbabwe has two major factories that have been manufacturing chrysotile asbestos cement products since the 1940s. Exposure monitoring of airborne fibres has been ongoing since the early 1990s. This study examines trends in personal exposure chrysotile asbestos fibre concentrations for the period 1996-2016. Close to 3000 historical personal exposure measurements extracted from paper records in the two factories were analysed for trends in exposure. Exposure over time was characterised according to three time periods and calendar years. Mean personal exposure chrysotile asbestos fibre concentrations generally showed a downward trend over the years in both factories. Exposure data showed that over the observed period 57% and 50% of mean personal exposure chrysotile asbestos fibre concentrations in the Harare and Bulawayo factories, respectively, were above the OEL, with overexposure being exhibited before 2008. Overall, personal exposure asbestos fibre concentrations in the factories dropped from 0.15 f/mL in 1996 to 0.05-0.06 f/mL in 2016-a decrease of 60-67%. These results can be used in future epidemiological studies, and in predicting the occurrence of asbestos-related diseases in Zimbabwe.

Accessing Occupational Health Services in the Southern African Development Community Region.

Only 15% of the global population has access to occupational safety and health services. In Africa, only 5% of employees working from major establishments have access to occupational health services (OHS). Access to primary health care (PHC) services is addressed in many settings and inclusion of OHS in these facilities might increase efficiency in preventing occupational diseases. A cross-sectional study was conducted in four Southern African Development Community (SADC) countries aiming at assessing the availability of OHS at PHC facilities and the organization of OHS. We conducted a literature review to assess the provision and organization of OHS services. In addition to the review, a total of 23 doctors from Zambia were interviewed using questionnaires in order to determine the availability of OHS and training. Consultations with heads of ministries were done in four SADC countries. Results showed that in the SADC region, OHS are fragmented and lack a comprehensive approach. In addition, out of 23 PHC facilities, only two (13%) provided occupational health and PHC. However, OHS provided at PHC facilities were limited to TB screening and audiometric testing. Our study showed a huge inadequacy of trained occupational health practitioners. This study supports the World Health Organization's advocacy to integrate OHS at the PHC level.

Health-related quality of life (EQ-5D + C) among people living in artisanal and small-scale gold mining areas in Zimbabwe: a cross-sectional study.

BACKGROUND: In Zimbabwe, an estimated 500,000 people work in the sector of artisanal and small-scale gold mining (ASGM). Two million Zimbabweans are dependent on this sector. Using mercury is common to extract gold from ore. Long term exposure to mercury can cause various adverse health conditions including chronic mercury intoxication. The influence of these adverse health effects on the health-related quality of life (HRQoL) is still unknown. The aim of this study is to assess the HRQoL of people who identify themselves as miners, and to analyze potential influencing factors, such as age, years of working with mercury and health conditions caused by mercury exposure. METHODS: This cross-sectional study assessed the HRQoL using the standardized EQ-5D + C (3 L) questionnaire and collected human specimens (blood, urine) of people living and possibly working in ASGM areas in Zimbabwe. Factors such as age, years of working with mercury and adverse health conditions possibly caused by mercury exposure were analyzed with regards to their influence on the HRQoL. RESULTS: The 207 participants (82% male, mean age 38 years) reported 40 different health states. Of the study participants 42.5% reported to be in complete good health while 57.5% reported being unwell in different ways. Nine participants (4.3%) were identified with chronic mercury intoxication, whereas 92 participants (33.3%) had mercury levels above the "Alert" threshold in at least one specimen. Having chronic mercury intoxication has a significant negative influence on the HRQoL, when taking into account age, gender and years of working with mercury. Cognitive problems were the most reported in the questionnaire, however, the association between this domain separately and the HRQoL was not verified. CONCLUSION: This study shows that adverse health effects caused by chronic exposure to mercury, have a negative influence on the HRQoL among people living in ASGM areas.

Artisanal and small-scale gold mining: A cross-sectional assessment of occupational mercury exposure and exposure risk factors in Kadoma and Shurugwi, Zimbabwe.

In artisanal and small-scale gold mining (ASGM) the toxic metal mercury is used for gold extraction. The objective of this cross-sectional study was to assess mercury concentrations in urine and blood and mercury-related symptoms of participants identifying themselves as miners from Kadoma and Shurugwi, Zimbabwe. Moreover, we aimed to explore possible risk factors influencing mercury body burden. In 2019, urine and blood samples of 207 participants were collected and analyzed for mercury using atomic absorption spectroscopy. All participants answered questions regarding their exposure risks. The median urine mercury value was 4.75 µg/L with a maximum of 612 µg/L. Median mercury concentration in creatinine corrected urine values was 3.98 µg/g with a maximum value of 478 µg/g. The median blood mercury value was 2.70 µg/L with a maximum of 167 µg/L. Correlations between exposure risks factors such as the lack of retort use and elevated mercury values were demonstrated. ASGM is very common in Zimbabwe. Thus, mercury exposure is a major occupational health risk for miners. Moreover, this study emphasizes the impact of exposure risk factors on the mercury body burden.

Review of Occupational Health and Safety Organization in Expanding Economies: The Case of Southern Africa.

BACKGROUND: Globally, access to occupational health and safety (OHS) by workers has remained at very low levels. The organization and implementation of OHS in South Africa, Zimbabwe, Zambia, and Botswana has remained at suboptimal levels. Inadequacy of human resource capital, training, and education in the field of OHS has had a major negative impact on the improvement of worker access to such services in expanding economies. South Africa, Zimbabwe, Zambia, and Botswana have expanding economies with active mining and agricultural activities that pose health and safety risks to the working population. METHODS: A literature review and country systems inquiry on the organization of OHS services in the 4 countries was carried out. Because of the infancy and underdevelopment of OHS in southern Africa, literature on the status of this topic is limited. RESULTS: In the 4 countries under review, OHS services are a function shared either wholly or partially by 3 ministries, namely Health, Labor, and Mining. Other ministries, such as Environment and Agriculture, carry small fragments of OHS function. The 4 countries are at different stages of OHS legislative frameworks that guide the practice of health and safety in the workplace. Inadequacies in human resource capital and expertise in occupational health and safety are noted major constraints in the implementation and compliance to health and safety initiatives in the work place. South Africa has a more mature system than Zimbabwe, Zambia, and Botswana. Lack of specialized training in occupational health services, such as occupational medicine specialization for physicians, has been a major drawback in Zimbabwe, Zambia, and Botswana. DISCUSSION: The full adoption and success of OHS systems in Southern Africa remains constrained. Training and education in OHS, especially in occupational medicine, will enhance the development and maturation of occupational health in southern Africa. Capacitating primary health services with basic occupational health knowledge would be invaluable in bridging the current skills deficit. Introducing short courses and foundational tracks in occupational medicine for general medical practitioners would be invaluable.